Knowledge

What are the common faults of metal rolling motors?

Nov 01, 2024 Leave a message

1. Electrical fault
Short circuit fault:
Phase-to-phase short circuit: Due to the insulation damage of the motor winding, a short circuit occurs between the windings of different phases. It may be caused by insulation aging, overvoltage shock, mechanical damage, etc. due to long-term operation. Phase-to-phase short circuit will generate a huge short-circuit current, causing the motor to heat up rapidly or even burn out.
Turn-to-turn short circuit: Short circuit between different turns in the same phase winding. It may be caused by poor winding manufacturing, insulation material defects, overcurrent shock, etc. Turn-to-turn short circuit will increase the motor current and unbalance the magnetic field, causing motor vibration, increased noise, and increased temperature.
Ground fault:
Winding grounding: The motor winding is electrically connected to the casing or other grounded parts. The reasons may be winding insulation damage, moisture, corrosion, etc. Ground fault will make the motor casing electrified, threatening personal safety, and at the same time causing the protection device to operate and stop the motor.
Overload fault:
Motor overload: During metal rolling, if the load exceeds the rated load of the motor, the motor will be overloaded. Overload will increase the motor current and temperature. Long-term overload will damage the motor insulation and shorten the motor life.
Frequent start-up: In metal rolling production, the motor may need to be started frequently. Frequent start-up will increase the motor temperature, accelerate insulation aging, and easily cause overload failure.
Phase failure:
Power supply phase failure: One phase of the power supply is disconnected or has poor contact, causing the motor to run in phase failure. Phase failure will cause the motor magnetic field to be unbalanced, resulting in greater vibration and noise, increased current, increased temperature, and easy to burn the motor.
Motor winding break: A broken wire inside the motor winding will also cause a phase failure. It may be caused by manufacturing defects, overcurrent shock, mechanical damage, etc.
2. Mechanical failure
Bearing failure:
Wear: Long-term operation will cause wear between the bearing rolling element and the raceway, resulting in increased bearing clearance, increased motor vibration and noise. When the wear is severe, the bearing will be stuck and the motor will not be able to operate normally.
Overheating: Poor bearing lubrication, overload operation, improper installation, etc. may cause bearing overheating. Overheating will shorten the bearing life and even damage the bearing.
Damage: Bearing damage may occur due to external impact, improper assembly, quality problems, etc. Bearing damage will change the gap between the motor rotor and stator, generate friction, and cause motor vibration, increased noise, and increased temperature.
Shaft failure:
Bending: If the motor is subjected to external impact or uneven force during installation, transportation or operation, it may cause the shaft to bend. Shaft bending will cause uneven air gap between the motor rotor and stator, generate vibration and noise, and affect motor performance and life.
Breakage: If the shaft is subjected to excessive torque or fatigue stress during long-term operation, it may break. Shaft breakage will cause the motor to stop running immediately, seriously affecting production.
Fan failure:
Blade damage: If the fan blade is hit by foreign objects or worn for a long time during operation, the blade may be damaged. Blade damage will affect the heat dissipation effect of the motor and increase the temperature of the motor.
Loose fan: Loose connection between the fan and the motor shaft will cause the fan to run unstably, generate vibration and noise. In severe cases, the fan may fall off, causing damage to the motor and surrounding equipment.
3. Other faults
Overheating fault:
Poor heat dissipation: Failure of the heat dissipation system of the motor, such as fan damage, ventilation duct blockage, etc., will cause poor heat dissipation of the motor and increase the temperature. Overheating will accelerate the aging of the motor insulation and reduce the performance and life of the motor.
Excessive ambient temperature: If the operating environment temperature of the motor is too high, the motor temperature will also rise. In a high temperature environment, the heat dissipation effect of the motor will be affected, and overheating faults are prone to occur.
Vibration fault:
Motor imbalance: Motor rotor imbalance, improper installation, bearing wear and other reasons may cause motor vibration. Vibration can loosen and damage the parts of the motor, affecting the performance and life of the motor.
Unbalanced rolling load: During the metal rolling process, if the load is unbalanced, the motor will be subjected to uneven force and vibrate. The vibration will be transmitted to the foundation and surrounding equipment of the motor, affecting the stability of the entire production system.
Noise fault:
Internal motor fault: Motor bearing fault, winding fault, fan fault, etc. may cause the motor to generate abnormal noise. Noise affects the working environment and may also be a precursor to motor failure, which needs to be checked and handled in time.
Transmission system failure: Failures in the transmission system between the motor and the rolling equipment, such as gear wear, loose couplings, etc., may also cause increased noise. Noise affects the normal operation of the equipment and may also affect the health of the operator. If you want to know about the common failures of metal rolling motors, you can contact MCM Electric Machinery and we will do our best to help you!

Send Inquiry