1. Electrical fault
1. Winding fault
Short circuit fault
Turn-to-turn short circuit: When the motor runs for a long time or is subjected to overvoltage shock, the inter-turn insulation of the winding may be damaged, forming an inter-turn short circuit. The inter-turn short circuit will reduce the equivalent resistance of the winding and increase the current, which will cause local overheating. For example, in a frequently started and stopped Rolling Mill Motor, the current shock at each start may gradually destroy the inter-turn insulation.
Phase-to-phase short circuit: Phase-to-phase short circuit may be caused by aging of the phase insulation, moisture or mechanical damage to the motor. Phase-to-phase short circuit will cause serious imbalance of the three-phase current of the motor, generate a large short-circuit current, and may instantly burn the winding of the motor.
Open circuit fault
The wire of the winding may break and cause an open circuit when it is subjected to mechanical stress (such as vibration), thermal stress or chemical corrosion for a long time. When the winding is open circuit, the motor cannot operate normally, and the motor may not start or suddenly stop during operation.
Insulation aging and breakdown
The environment of the rolling mill is usually harsh. High temperature, humidity, dust and corrosive gases will accelerate the aging of the insulation of the motor winding. When the insulation ages to a certain extent, insulation breakdown may occur, causing the motor winding to be conductive with the iron core or casing, resulting in leakage or even short circuit failure.
2. Power failure
Lack of phase operation
One phase of the three-phase power supply is disconnected, which may be caused by a blown fuse, poor contact of the contactor contacts, or disconnection of the power cord. When the Rolling Mill Motor is running in a phase-loss mode, the current of the other two phases will increase sharply, causing the motor to overheat, intensify vibration, and reduce output torque, seriously affecting the normal rolling production.
Voltage fluctuation
The unstable power supply grid or the start and stop of large equipment in the workshop may cause voltage fluctuations. If the voltage is too high, the magnetic flux of the motor core will be saturated, increasing iron loss, and the motor current will increase, causing the winding to overheat; if the voltage is too low, the torque of the motor will decrease, which may not meet the torque requirements of the rolling process, and even cause the motor to stall.
2. Mechanical failure
1. Bearing failure
Wear
When the Rolling Mill Motor is running under high load, the bearing is subjected to large radial and axial forces. Long-term operation will cause wear of the bearing's ball, raceway and other parts. The worn bearing will increase the axial and radial clearance of the motor rotor, resulting in increased vibration and noise of the motor, while affecting the rotation accuracy of the motor, and thus affecting the quality of the rolled product.
Overheating and poor lubrication
Insufficient grease, deterioration or poor bearing seal will cause impurities to enter the bearing, which will cause the bearing to overheat. Overheating of the bearing will further accelerate the wear of the bearing, and in severe cases, it will cause the bearing to get stuck and the motor cannot operate normally.
2. Rotor failure
Rotor imbalance
During the manufacturing process, if the mass distribution of the rotor is uneven, or the mass distribution of the rotor changes due to wear, corrosion and other reasons during operation, it will cause the rotor to be unbalanced. Rotor imbalance will cause strong vibration of the motor, which will not only affect the service life of the motor itself, but may also be transmitted to the rolling equipment, affecting the accuracy of the rolling process.
Bending of the rotor shaft
The motor may bend due to external impact (such as during transportation or installation) or long-term operation under unbalanced load. The bending of the rotor shaft will make the air gap of the motor uneven, increase the vibration and noise of the motor, and also aggravate the wear of the bearings, affecting the normal operation of the motor.
3. Coupling failure
Wear and looseness
The coupling is an important component connecting the Rolling Mill Motor and the rolling equipment. During long-term operation, the connecting parts of the coupling may wear or loosen due to vibration, impact and other reasons. Coupling wear will reduce the power transmission efficiency, while looseness may cause unstable connection between the motor and the rolling equipment, generate vibration and impact, and affect the normal rolling production.
III. Control failure
1. Control system failure
The control system of the Rolling Mill Motor includes components such as controllers, sensors, and inverters (for AC motors). If the controller fails, such as program errors, chip damage, etc., the motor may not be able to operate according to the predetermined speed, torque and other parameters. Sensor failure (such as speed sensor, temperature sensor, etc.) will make the control system unable to accurately obtain the operating status information of the motor, and thus unable to perform effective control and protection. Frequency converter failure (for AC variable frequency motors) may affect the speed regulation performance of the motor, resulting in speed instability, inability to regulate speed, and other problems.
2. Abnormal speed feedback
The speed feedback device (such as an encoder) is used to feedback the actual running speed of the motor to the control system. If the speed feedback device fails, such as damage to the encoder's code disk, a broken signal line, etc., the control system will receive incorrect speed information, thereby affecting the speed control accuracy of the motor. The motor may experience speed fluctuations, overspeed or stall, which will seriously affect the stability of rolling production and product quality.
What are the main faults of Rolling Mill Motor?
Sep 30, 2024
Leave a message
Send Inquiry

