Knowledge

Precautions for maintenance and servicing of Mining Electric Motor

Nov 13, 2024 Leave a message

1. Safety first
Shutdown operation: Before any maintenance and servicing work, the motor must be stopped and the power must be cut off. Make sure the power switch is in the "off" position and hang a "no closing" warning sign to prevent accidental start-up.
Personal protection: Maintenance personnel should wear appropriate personal protective equipment, such as safety helmets, safety shoes, gloves, goggles, etc. When performing maintenance involving electrical parts, insulating tools should also be used to avoid the risk of electric shock.
Working environment: Ensure that maintenance work is carried out in a safe, dry and well-ventilated environment. Avoid operating in a humid, dusty, flammable and explosive environment to avoid safety accidents.
2. Correct operation
Follow the manual: Operate strictly in accordance with the motor's instruction manual and maintenance manual. Understand the structure, performance, maintenance requirements and safety precautions of the motor to ensure the correctness and effectiveness of the maintenance work.
Tool use: Use the correct tools for maintenance and servicing work. Avoid using inappropriate tools to avoid damaging motor components or causing safety accidents. For example, use special wrenches, screwdrivers, pullers and other tools for disassembly and installation.
Operation sequence: Perform maintenance work in the correct operation sequence. For example, when disassembling motor parts, the external connectors should be removed first, and then the internal parts; when installing, they should be done in the opposite order. Avoid changing the operation sequence at will to avoid affecting the performance and life of the motor.
3. Cleaning and inspection
Cleaning: Clean the motor regularly to remove dust and dirt from the housing, heat sink, fan and other parts. You can use compressed air, a clean wet cloth or a vacuum cleaner for cleaning, but be careful not to let water or detergent enter the inside of the motor.
Check the appearance: Check whether the appearance of the motor is damaged, deformed, cracked, etc. In particular, check whether the junction box, cable, anchor bolts and other parts are firm and reliable. If there is a problem, it should be repaired or replaced in time.
Check the electrical part: Check the electrical part of the motor regularly, including the terminal, cable, contactor, relay, etc. Check whether the wiring is loose, oxidized or burned; whether the cable is damaged, short-circuited or grounded; whether the electrical components such as contactors and relays are working properly. If there is any problem, it should be repaired or replaced in time.
Check the mechanical part: Check the mechanical part of the motor, including bearings, shafts, fans, couplings, etc. Check whether the bearings are worn, overheated, noisy, etc.; whether the shafts are bent, worn, etc.; whether the fans are damaged, deformed, etc.; whether the couplings are loose, worn, etc. If there is any problem, it should be repaired or replaced in time.
4. Lubrication and maintenance
Lubrication: Lubricate the bearings of the motor regularly according to the instructions and maintenance manual of the motor. Select suitable grease or lubricating oil, and fill it according to the prescribed methods and cycles. Be careful not to overfill grease to avoid overheating of the bearings.
Maintenance: Maintain the motor regularly, including replacing worn parts, adjusting clearances, tightening bolts, etc. According to the use and maintenance requirements of the motor, formulate a reasonable maintenance plan, and strictly follow the plan for maintenance work.
5. Fault handling
Fault diagnosis: When the motor fails, it should be diagnosed in time to find out the cause of the fault. The diagnosis can be made by observing the fault phenomenon, measuring electrical parameters, and checking mechanical parts. Common causes of failure include overload, phase loss, short circuit, grounding, bearing damage, friction between stator and rotor, etc.
Fault handling: Take appropriate maintenance measures according to the cause of the failure. For some minor faults, such as loose wiring, poor bearing lubrication, etc., they can be repaired by on-site operators. But for some larger faults, such as winding short circuit, bearing damage, etc., professional maintenance personnel should be asked to repair. When repairing the motor, it is necessary to strictly follow the operating procedures to ensure the quality of maintenance.
Recording and reporting: Record the fault conditions of the motor, including fault phenomena, diagnostic results, and maintenance measures. At the same time, the fault conditions should be reported to superiors or relevant departments so that timely measures can be taken to avoid affecting production.
When maintaining and servicing Mining Electric Motor, strictly abide by the safety operating procedures, operate correctly, regularly clean, inspect, lubricate and maintain, handle faults in time, ensure the performance and life of the motor, and provide reliable power guarantee for mining production.
If you want to know what you need to pay attention to when maintaining and servicing Mining Electric Motor, you can contact MCM Electric Machinery, and we will do our best to help you!

Send Inquiry