1. Daily inspection
Appearance inspection:
Check the appearance of the motor every day to see if there is obvious damage, cracks or deformation. Pay special attention to the motor housing, terminal box and cooling fan.
Check the nameplate of the motor to ensure that the motor model, rated power, voltage, current and other parameters are consistent with the actual use.
Temperature inspection:
Touch the motor housing with your hand to feel whether its temperature is normal. If it feels overheated, stop the machine immediately for inspection.
Infrared thermometers can be used to measure the surface temperature and bearing temperature of the motor regularly. Generally speaking, the surface temperature of the motor should not exceed 40℃ above the ambient temperature, and the bearing temperature should not exceed 95℃.
Sound inspection:
Listen to the sound of the motor when it is running to determine whether there is any abnormal noise. Such as friction, impact, humming, etc. Abnormal noise may be a sign of bearing damage, friction between the stator and the rotor, fan failure and other problems.
If abnormal noise is found, stop the machine immediately for inspection, find out the source of the noise and repair it.
Vibration inspection:
Feel the vibration of the motor with your hand to determine whether there is obvious vibration. If the vibration is too large, it may be due to problems such as loose installation of the motor, bearing wear, rotor imbalance, etc.
A vibration tester can be used to regularly measure the vibration amplitude and frequency of the motor. Generally speaking, the vibration amplitude of the motor should not exceed 0.1mm.
2. Regular maintenance
Cleaning and maintenance:
Clean the motor regularly to remove dust and dirt from the housing, cooling fan, and junction box. Compressed air or a clean damp cloth can be used for cleaning, but be careful not to let water or detergent enter the inside of the motor.
Clean the ventilation duct of the motor to ensure good ventilation and prevent the motor from overheating. A vacuum cleaner or compressed air can be used to clean dust and debris in the ventilation duct.
Lubrication maintenance:
Lubricate the bearings of the motor regularly to reduce friction and wear and extend the service life of the bearings. According to the use of the motor and the type of bearing, select the appropriate lubricant and add it according to the prescribed lubrication cycle.
Pay attention to the quality and cleanliness of the grease, and avoid using inferior or expired grease. When adding grease, be careful not to overfill to avoid overheating the bearing.
Electrical inspection:
Check the electrical connections of the motor regularly to ensure that the wiring is firm and the contact is good. Check whether the wiring terminals in the junction box are loose, oxidized or burned.
Measure the insulation resistance of the motor to determine whether its insulation performance is good. Generally speaking, the insulation resistance of the motor should not be less than 0.5MΩ. If the insulation resistance is too low, it should be dried or the insulation material should be replaced in time.
Check the starting equipment and protection devices of the motor to ensure their normal operation. For example, contactors, thermal relays, circuit breakers, etc., check whether their contacts are burned, adhered, etc., and whether the protection parameters are set correctly.
3. Fault handling
Fault diagnosis:
When the motor fails, it should be diagnosed in time to find out the cause of the fault. It can be diagnosed by observing the fault phenomenon, measuring electrical parameters, and checking mechanical parts.
Common causes of failure include overload, phase loss, short circuit, grounding, bearing damage, stator and rotor friction, etc. Take corresponding maintenance measures according to the cause of the failure.
Maintenance method:
For some minor faults, such as loose wiring, poor bearing lubrication, etc., they can be repaired by on-site operators. However, for some larger faults, such as winding short circuit, bearing damage, etc., professional maintenance personnel should be asked to repair them.
When repairing the motor, strictly follow the operating procedures to ensure the quality of the repair. After the repair, a trial run should be carried out to check whether the motor is operating normally.
4. Precautions
Safety first:
When performing maintenance on the motor, ensure safety. First, cut off the power supply and hang a warning sign of "No Closing" on the power switch. Secondly, follow the operating procedures and use appropriate tools and equipment to avoid safety accidents.
Environmental requirements:
The motor should be installed in a dry, ventilated and clean environment. Avoid installing it in humid, dusty, corrosive gas or flammable and explosive places. If the environmental conditions are harsh, appropriate protective measures should be taken, such as installing protective covers, ventilation equipment, etc.
Training and management:
Train the operators to make them familiar with the operating procedures and maintenance methods of the motor. Establish a sound motor management system, regularly inspect, maintain and maintain the motor, and record the operation and maintenance history of the motor.
For important motors, spare motors can be established so that they can be replaced in time when a failure occurs to ensure the continuity of production.
If you want to know how to maintain Mining Electric Motor, you can consult our professional technicians, we will serve you wholeheartedly 24 hours a day!
What are the maintenance methods of Mining Electric Motor?
Nov 11, 2024
Leave a message
Send Inquiry

